Skip to content
TechnoGuru — Think Technology, Think TechnoGuru

Projector Throw · Ultra-short-throw laser TV

XGIMI Aura 2 throw distance & placement

Problem. An ultra-short-throw laser TV lives close to the wall it projects onto, so the real question is not how far back to sit the projector but how much sideboard or console depth the room can spare beneath the screen. For the XGIMI Aura 2, that placement decision needs to be checked against the actual throw ratio rather than assumed from habit with a conventional projector.

Answer. At a 100-inch 16:9 screen (2.21 m wide), the XGIMI Aura 2's 0.177:1 throw ratio places the lens about 0.39-0.39 m from the wall. In practice, the unit sits on a low console directly beneath the image rather than back in the room, so the placement question becomes console depth and lens-to-wall clearance, not projector throw across the room.

02 / In depth

How this preset reads — the engineering view.

The Aura 2 uses a ust (ultra-short-throw) lens with a 0.177-0.177:1 throw ratio, meaning almost no distance separates the projector from the screen it fills. At 100 inches that works out to 0.39-0.39 m, so the unit sits on furniture directly under the image rather than being positioned across the room as a conventional long-throw projector would be.

With 2300 lumens, a native 3840x2160 (4K) panel, and an led-laser-hybrid light source, the Aura 2 is built for a controllable-light living space rather than a fully daylit room; laser-hybrid sources also tend to hold brightness and colour more consistently over long viewing hours than lamp-based units. This combination suits a media wall or lounge where the screen size and seating are fixed and the household wants a large image without a ceiling or rear-wall mount.

Use the calculator's screen-size control to see how the 0.39 m figure moves as the image grows or shrinks — because the throw ratio is fixed, a larger screen simply asks for slightly more clearance between the console and the wall, not a repositioned projector. For ultra-short-throw units like this, also confirm the console or cabinet has enough depth to hold the unit level and square to the wall, and note that an ambient-light-rejecting (ALR) screen is commonly paired with UST projectors to preserve contrast in rooms that are not fully darkened.

The calculator resolves throw distance only; it does not evaluate screen gain or ALR performance, how much ambient light the room actually admits, mounting or console suitability, the exact lens variant if a model line ships more than one, or audio output and speaker placement. Those factors sit alongside the throw figure and are worth checking against the room separately.

What this preset deliberately does not solve

  • The 0.39-0.39 m figure is a lens-to-screen throw distance, not a required gap from the wall to the back of the cabinet housing the projector.
  • Ultra-short-throw placement is unusually sensitive to how level and square the supporting surface is; small tilts shift image geometry more than they would on a long-throw setup.
  • Published throw ratios can vary slightly by unit and firmware calibration; treat the calculator's figure as a planning distance to confirm on site, not a fixed installation spec.

How this preset differs from its siblings

Ultra-short-throw laser TVs as a category cover a range of throw ratios, and even a modest difference changes how close to the wall the unit needs to sit for the same screen size. The Aura 2's 0.177:1 ratio and 2300-lumen, 4K native panel give it a specific placement and brightness profile that will not match every other UST model's numbers, which is why this page exists separately rather than relying on a generic ultra-short-throw estimate.

03 / Hydrated calculator

Try the configuration — live.

The calculator below is preloaded with this preset’s state. Adjust any input — your URL stays shareable.

Loading the calculator…

· Other presets for projector throw calculator

· Next

Brief us on the project — with this configuration.

Presets are a typology starting point. The brief wizard captures the room geometry, programme and constraints we need to translate this configuration into a real design.